Livorsi DTS Controls Manuel d'utilisateur télécharger pdf

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 1 of 12

715 Center Street

Grayslake IL 60030

P: 847-752-2700

F: 847-752-2415

E: info@livorsi.com

This document is written to aid our dealers, boat builders, and company service

personnel in the proper installation or service of our products. Persons who are not

familiar with these or similar products produced by Livorsi Marine, Inc., and who have

not been trained in the recommended servicing or installation procedures should have

the work performed by an authorized Mercury Marine dealer technician. Improper

installation or servicing of the Mercury Marine or Livorsi Marine product could result in

damage to the product or personal injury to the installer or persons operating the

product.

NOTICE

After completing installation, these instructions should be kept with the product for the

owner’s future use.

NOTICE

Notice to Personnel Installing this Kit

The installation of this product requires an installer who is specifically trained to work

on Mercury Marine’s or Livorsi Marine’s digital throttle and shift (DTS) systems. The

installer must be trained in the proper installation, electronic calibration, and operation

of the DTS system. Failure to correctly install this product may make this product and

/or the DTS system inoperable or unsafe for use.

Avoid possible injury or equipment damage. After installing this control, electronically

calibrate the digital throttle and shift (DTS) system. Do not attempt any calibration

unless you have been specifically trained in Mercury Marine’s DTS systems. Improper

electronic calibration of the DTS system will make this control and/or the DTS system

inoperable or unsafe.

CAUTION

Electrical Requirements

DTS equipped boats require that the electrical systems meet the following guidelines:

 Use only marine starting batteries with a 1000 mca /800 cca/ 180 amp hour rating

or higher. Deep cycle batteries do not deliver the power required for the DTS

system.

 Secure all battery cables with standard hex nuts, tightened to 13.5 Nm (120 lb. in.)

Do not use wing nuts, as they will not secure the battery cables properly.

 Ensure that the battery cable size (cross section) meets the minimum size

requirements for the length of cable used. Refer to the installation manual supplied

with the engine.

 Ensure that all power supply connections are clean and tight.

Livorsi DTS Controls

Single/Dual Engine Digital Throttle & Shift Installation

1 2 3 4 5 6 ... 17 18

Résumé du contenu

Page 1 - Livorsi DTS Controls

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 1 of 12 715 Center Street Grayslake IL 60030 P: 847-752-2700 F: 847-752-2

Page 2 - Dimensions and Clearances

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 10 of 12 Control Connection Harness Connection Starboard Shift Potentiomete

Page 3

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 11 of 12 Control Quadrant Operation Shift Lever  Shift into reverse by mo

Page 4 - Important:

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 12 of 12 Aft Cant Models In-Handle Trim Switch 1. To tr

Page 5

Livorsi DTS ControlArchitecture Drawing- Single EngineThe following information has been gathered from Mercury Marine and may not be current. Please c

Page 6 - Neutral Safety Switch

Livorsi DTS ControlArchitecture Drawing-Dual EngineThe following information has been gathered from Mercury Marine and may not be current. Please cont

Page 7 - Rigging the Control

(86 mm)3 3/8 in.Overall Surface AreaCutout Area(73 mm)2 7/8 in.Livorsi DTS Controls Flat BaseSingle Engine (2 handle)5 1/8 in. (130 mm)7 3/4 in. (1

Page 8

(144 mm)Twin Engine 5 11/16 in.Overall Surface AreaCutout AreaTwin Engine 5 3/16 in. (131 mm)Livorsi DTS Controsl Flat BaseTwin Engine ( four handl

Page 9

7 3/4 in. (197 mm)3 3/8 in. (86 mm)2 7/8 in. (73 mm)Livorsi DTS ControlsContour BaseSingle Engine (2 handle)When printing thistemplate, make sure t

Page 10

7 3/4 in. (197 mm)5 3/16 in. (132 mm)5 11/16 in. (144 mm)Livorsi DTS ControlsContour BaseTwin Engine (4 handle)When printing thistemplate, make sur

Page 11 - Throttle Lever

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 2 of 12 Dimensions and Clearances Location Requirements Understand th

Page 12 - Control Quadrant Maintenance

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 3 of 12 Livorsi DTS Control Dimensions See cutout templates at the end of th

Page 13 - Livorsi DTS Control

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 4 of 12 Livorsi DTS Control Dimension Chart Number of Handles “A” DIM “B” D

Page 14

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 5 of 12 3. Use a #22 drill bit to drill the four required holes. Drill perpe

Page 15

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 6 of 12 Installing the Control to the Console 1. Secure the c

Page 16

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 7 of 12 Rigging the Control Connecting the SmartCraft Harness (Single Engine)

Page 17

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 8 of 12 1. Connect the “LEVER 1” connector on the DTS command module harnes

Page 18

Livorsi DTS Controls- Single/Dual Engine Installation APRIL 2012 Page 9 of 12 Connecting the SmartCraft Harness (Dual Engine) The following proced

Plus de documents pour Capteurs Livorsi DTS Controls

Voir le document Livorsi DTS Controls Manuel d'utilisateur

Livorsi DTS Controls Manuel d'utilisateur (19 pages)

Commentaires sur ces manuels

Pas de commentaire

Livorsi DTS Controls Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Capteurs Livorsi DTS Controls. Livorsi DTS Controls User Manual Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Capteurs Livorsi DTS Controls

Commentaires sur ces manuels

Produits connexes et manuels pour Capteurs Livorsi DTS Controls